电话:
400-7060-959
传真:
+86 10 56315212-8813
电子邮件:
orders@antibodies-online.cn

ABTS Antioxidant Capacity Assay Kit

BCA Colorimetric Beverages, Cell Lysate, Food, Tissue Homogenate Uncoated
产品编号 ABIN7384573
发货至: 中国
  • 检测方法
    Colorimetric
    检测范围
    2.5-130 μg/mL
    最低检测浓度
    2.5 μg/mL
    应用范围
    Biochemical Assay (BCA)
    原理
    The kit is designed for the antioxidant capacity measurement in foods, beverages and biological samples.
    样品类型
    Beverages, Cell Lysate, Food, Tissue Homogenate
    特异性
    Specific for antioxidant activity determination.
    产品特性
    ABTS assay kit is recommended for total antioxidant activity of solutions of pure substances, aqueous mixtures and beverages. The assay described here involves the direct production of the blue/green ABTS•+ chromophore. This has absorption maxi
    组件
    Plate and the reagents neccesary to perform the assay.
    试剂未包括
    Phosphate Buffer, Ethanol, Pipettes, Reaction tubes, plate reader.
  • 样本量
    5 μL
    实验时间
    15 min
    板类型
    Uncoated
    试剂准备

    Reagents preparation: 1. For ABTS Reagent A dilute it with EtOH (for phenolic compounds and extracts) or PBS (for plasma) to an absorbance of 0.70 (±0.02) at 734 nm and 30 °C. Approximately a relation radical ABTS / EtOH 1 to 40. This solution is called ABTS Reagent A Solution. Keep it at -20 °C. 2. For standard solution preparation, add exactly 1 mL of deionized water to the ABTS standard vial. After that make the transfer of the 1 mL to a vial with higher capacity and fill up to 10 mL final volume. Once dissolved, keep it at -20 °C. Sample preparation: Dilute your sample in EtOH (for phenolic compounds and food extracts) or PBS (for plasma) such that, after introduction of 5 μL of each aliquot into 200 μL of ABTS Reagent A Solution, they produce between 5 % -35 % inhibition of the blank absorbance (ABTS•+ alone).

    实验流程

    Standard Preparation Antioxidant activity is expressed as CEAC (Vitamin C equivalents antioxidant capacity). Prepare calibration curves in 1 mL tubes as shown in Table 1 (see kit Booklet). Keep it at -20 °C.
    Performing the assay:1.Add 5 μL of the sample or standard in each well. 2.Add 200 μL of ABTS Reagent A Solution previously diluted (see reagents preparation) in each well. 3.Mix the mixture at 30 °C for 4 minutes under continuous stirring. 4.Read the absorbance at 734 nm at 30 °C.

    结果分析

    1.Calculate the absorbance at 734 nm as percentage of the absorbance of the uninhibited radical cation solution (Blank) according to the equation: Inhibition of A734 (%) = (1-Af/A0) x 100 Where A0 is the absorbance of uninhibited radical cation and Af is the absorbance measured 4 min after the addition of antioxidant samples. 2. Plot the inhibition of A734 of standards as function of their final concentrations (Table 1 in kit booklet). See Figure 2 (see images) for a typical standard curve. 3.Calculate the CEAC value of the samples using the equation obtained from the linear regression of the standard curve substituted of A734 values for each sample. CEAC (μM) = (sample inhibition A734- intercept)/slope

    限制
    仅限研究用
  • 储存液
    Sodium azide
    注意事项
    This product contains Sodium azide: a POISONOUS AND HAZARDOUS SUBSTANCE which should be handled by trained staff only.
    储存条件
    RT/-20 °C
    储存方法
    ABTS Reagent: -20 °C, ABTS Standard: RT
You are here:
客服