NPY ELISA 试剂盒

• Strip plates and additional reagents allow for use in multiple experiments
• Quantitative protein detection
• Establishes normal range
• The best products for confirmation of antibody array data

• Pre-Coated 96-well Strip Microplate
• Wash Buffer
• Standard Peptide
• Assay Diluent(s)
• Biotinylated Peptide
• HRP-Streptavidin
• TMB One-Step Substrate
• Stop Solution
• Assay Diagram
• Positive Control Sample
• Capture Antibody
• User Manual

• Distilled or deionized water
• Precision pipettes to deliver 2 μL to 1 mL volumes
• Adjustable 1-25 mL pipettes for reagent preparation
• 100 mL and 1 liter graduated cylinders
• Tubes to prepare standard and sample dilutions
• Orbital shaker
• Aluminum foil
• Saran Wrap
• Absorbent paper
• Microplate reader capable of measuring absorbance at 450nm
• SigmaPlot software (or other software that can perform four-parameter logistic regression models)

1. Prepare all reagents, samples and standards as instructed.
2. Add 100 μL detection antibody to each well.
3. Incubate 1.5 h at RT or O/N at 4 °C.
4. Add 100 μL standard or sample to each well.
5. Incubate 2.5 h at RT.
6. Add 100 μL prepared streptavidin solution.
7. Incubate 45 min at RT.
8. Add 100 μL TMB One-Step Substrate Reagent to each well.
9. Incubate 30 min at RT.
10. Add 50 μL Stop Solution to each well.
11. Read plate at 450 nm immediately.

1. Keep kit reagents on ice during steps. Equilibrate plate to room temperature before opening the sealed pouch.
   2. Briefly centrifuge the NPY Antibody vial (Item N) and reconstitute with 5 µL of ddH2O before use. Add 50 µL of 1x Assay Diluent E into the vial to prepare a detection antibody concentrate. Pipette up and down to mix gently.
   3. The antibody concentrate should then be diluted 100-fold with 1x Assay Diluent E. This is your anti-Neuropeptide Y antibody working solution, which will be used in step 2 of the Assay Procedure. NOTE: the following steps may be done during the antibody incubation procedure (step 2 of Assay Procedure).
   4. Briefly centrifuge the vial of biotinylated Neuropeptide Y peptide (Item F) and reconstitute with 20 µL of ddH2O before use. Add 10 µL of Item F to 5 m 1X Assay Diluent E. Pipette up and down to mix gently. The final concentration of biotinylated Neuropeptide Y will be 20 ng/mL. This solution will only be used as the diluent in step 5 of Reagent Preparation.
   5. Preparation of Standards: Label 6 microtubes with the following concentrations: 1000 ng/mL, 100 ng/mL, 10 ng/mL, 1 ng/mL, 100 pg/mL and 0 pg/mL. Pipette 450 µL of biotinylated Neuropeptide Y solution into each tube, except for the 1000 ng/mL (leave this one empty). It is very important to make sure the concentration of biotinylated Neuropeptide Y is 20 ng/mL in all standards. a. Briefly centrifuge the vial of standard Neuropeptide Y peptide (Item C) and reconstitute with 10 µL of ddH2O. In the tube labeled 1000 ng/mL, pipette 8 µL of Item C and 792 µL of 20 ng/mL biotinylated Neuropeptide Y solution (prepared in step 4 above). This is your Neuropeptide Y stock solution (1000 ng/mL Neuropeptide Y, 20 ng/mL biotinylated Neuropeptide Y). Mix thoroughly. This solution serves as the first standard. b. To make the 100 ng/mL standard, pipette 50 µL of Neuropeptide Y stock solution the tube labeled 100 ng/mL. Mix thoroughly. c. Repeat this step with each successive concentration, preparing a dilution series as shown in the illustration below. Each time, use 450 µL of biotinylated Neuropeptide Y and 50 µL of the prior concentration until 100 pg/mL is reached. Mix each tube thoroughly before the next transfer. d. The final tube (0 pg/mL Neuropeptide Y, 20 ng/mL biotinylated Neuropeptide Y) serves as the zero standard (or total binding).
   6. Prepare a 10-fold dilution of Item F. To do this, add 2 µL of Item F to 18 µL of 1X Assay Diluent E. This solution will be used in steps 7 and
   9.
   7. Positive Control Preparation: Briefly centrifuge the positive control vial and reconstitute with 100 µL of ddH2O before use (Item M). To the tube of Item M, add 101 µL 1x Assay Diluent E. Also add 4 µL of 10-fold diluted Item F (prepared in step 6) to the tube. This is a 2-fold dilution of the positive control. Mix thoroughly. The positive control is a cell culture medium sample that is meant to be a system control (to verify that the detection & kit components are working). It may be diluted further if desired, but be sure the final concentration of biotinylated Neuropeptide Y is 20 ng/mL.
   8. If Item B (20X Wash Concentrate) contains visible crystals, warm to room temperature and mix gently until dissolved. 1000 100 10 1 100 0 ng/mL ng/mL ng/mL ng/mL pg/mL pg/mL 50 µL 50 µL 50 µL 50 µL Dilute 20 µL of Wash Buffer Concentrate into deionized or distilled water to yield 400 µL of 1X Wash Buffer.
   9. Sample Preparation: Use 1X Assay Diluent E + biotinylated NPY to dilute samples, including serum/plasma, cell culture medium and other sample types. It is very important to make sure the final concentration of the biotinylated Neuropeptide Y is 20 ng/mL in every sample.
   Example: to make a 4-fold dilution of sample, mix together 5 µL of 10-fold diluted Item F (prepared in step 6), 182.5 µL of 1X Assay Diluent E, and 62.5 µL of your sample, mix gently. The total volume is 250 µl, enough for duplicate wells on the microplate. Do not use Item F diluent from Step 5 for sample preparation. If you plan to use undiluted samples, you must still add biotinylated Neuropeptide Y to a final concentration of 20 ng/mL.
   Example: Add 5 µL of 10-fold diluted Item F to 245 µL of sample.
   10. Briefly centrifuge the HRP-Streptavidin vial (Item G) before use. The HRP-Streptavidin concentrate should be diluted 400- fold with 1X Assay Diluent E.

Use 1X Assay Diluent E + biotinylated NPY to dilute samples, including serum/plasma, cell culture medium and other sample types. It is very important to make sure the final concentration of the biotinylated Neuropeptide Y is 20 ng/mL in every sample. EXAMPLE: to make a 4-fold dilution of sample, mix together 5 µL of 10-fold diluted Item F (prepared in step 6), 182.5 µL of 1X Assay Diluent E, and 62.5 µL of your sample, mix gently. The total volume is 250 µl, enough for duplicate wells on the microplate. Do not use Item F diluent from Step 5 for sample preparation. If you plan to use undiluted samples, you must still add biotinylated Neuropeptide Y to a final concentration of 20 ng/mL. EXAMPLE: Add 5 µL of 10-fold diluted Item F to 245 µL of sample.

1. Keep kit reagents on ice during reagent preparation steps. It is recommended that all standards and samples be run at least in duplicate.
   2. Add 100 µL anti-Neuropeptide Y antibody (see Reagent Preparation step 3) to each well. Incubate for 1.5 hours at 0 room temperature with gentle shaking (1-2 cycles/sec). You may also incubate overnight at 4 degrees C.
   3. Discard the solution and wash wells 4 times with 1x Wash Buffer (200-300 µL each). Washing may be done with a multichannel pipette or an automated plate washer. Complete removal of liquid at each step is essential to good assay performance. After the last wash, remove any remaining Wash Buffer by aspirating or decanting. Invert the plate and blot it against clean paper towels.
   4. Add 100 µL of each standard (see Reagent Preparation step 5), positive control (see Reagent Preparation step 7) and sample (see Reagent Preparation step 9) into appropriate wells. Be sure to include a blank well (Assay Diluent only). Cover wells and incubate for 2.5 hours at room temperature with gentle shaking (1-2 cycles/sec) or overnight at 4 °C.
   5. Discard the solution and wash 4 times as directed in Step
   3.
   6. Add 100 µL of prepared HRP-Streptavidin solution (see Reagent Preparation step 10) to each well. Incubate with gentle shaking for 45 minutes at room temperature. It is recommended that incubation time should not be shorter or longer than 45 minutes.
   7. Discard the solution and wash 4 times as directed in Step
   3.
   8. Add 100 µL of TMB One-Step Substrate Reagent (Item H) to each well. Incubate for 30 minutes at room temperature in the dark with gentle shaking (1-2 cycles/sec).
   9. Add 50 µL of Stop Solution (Item I) to each well. Read absorbances at 450 nm immediately. 1

Calculate the mean absorbance for each set of duplicate standards, controls and samples, and subtract the blank optical density. Plot the standard curve using SigmaPlot software (or other software which can perform four-parameter logistic regression models), with standard concentration on the x-axis and percentage of absorbance on the y-axis. Draw the best-fit curve through the standard points.